EMOVE Touring - Starter Guide

Setup & Maintenance Guides

 

EMOVE Touring Setup Guide

Quick Notes

What's inside the box for touring?

  • Scooter
  • Rubber Seal
  • Instruction Manual
  • Charger

 

EMOVE Touring Speed Mode Menu

Quick Notes

How to change Speed:

  • Click and hold the power
  • Click the power button again. (The huge number 1 in the LCD display should blink)
  • Press Mode to change the speed.

How to turn on your EMOVE Touring

Quick Notes

Turn the scooter on by holding the power button.
Note: If the scooter does not turn on Contact us.

 

Charging your EMOVE Touring

Quick Notes

  • On the front right of the scooter, under the rubber cap, you will see the power plug.
  • The charger light has two colors: Red and Green

Red - Plugged and Charged
Green - Fully Charged

Best practices: Do not keep the scooter on when you are charging. You can check the voltmeter to see the current voltage but turn if off immediately.

Note: Charger getting hotter is normal due to the size of the battery and shorter charging hours. You can place the charger box on top of the deck. Metal will help disperse the heat.

 

EMOVE Touring - Lights

Quick Notes

How to turn on head and tail lights:
You should see a switch button on the left handlebar. Slide up to turn on the head and tail lights.

How to turn the deck lights on:
On the front-right of the deck you will see a button. Click that to turn on the deck lights.

Note: On the left side of the handlebar, you will see a yellow button. This is a horn button for safety purposes. You should also see a bell attached to the rear brake.

 

Unfolding Your EMOVE Touring

Quick Notes

Step 1: To fold the scooter, press the tab down so the pin unlocks and fold the handlebars down to the base.

Step 2: To open the scooter, just push the pin down and lift the handlebars up.

Note: If you notice stem wiggle, you may need to tighten the rubber stop, and tighten the bottom screws to reinforce the stop.

 

EMOVE Touring Handlebars

Quick Notes

Step 1: Slide the part with the arrow towards the grip.
Step 2: Fold the handlebar down so you can see the screw inside.
Step 3: If the handlebar has too much play, loosen the screw.

Note: You may not successfully remove the play on your first try. Do a trial and error test. Do not loosen the screw too much as it will not allow you to attach it back to the T tube.

How to raise handlebar:

Step 1: Unlatch the lock on the clamp.
Step 2: Raise the handlebar.
Step 3: Do not forget to lock it after you’ve chosen the preferred height of your handlebar.

 

Maintaining Your EMOVE Touring

Quick Notes

How to fix Handle Bar Play issue:

Step 1: Slide the part with the arrow towards the grip.
Step 2: Fold the handlebar down so you can see the screw inside.
Step 3: If the handlebar has too much play, loosen the screw.

Note: You may not successfully remove the play on your first try. Do a trial and error test. Do not loosen the screw too much as it will not allow you to attach it back to the T tube.

Unaligned Handle bar / Straighten handle bar tutorial:

Step1: Loosen the screws on the stem of the scooter.
Step 2: Squeeze the wheel and adjust, so that the handlebar will be aligned to the wheel. You can use the hole in front of the touring as a guide to check whether the handlebar is aligned or not.
Step 3: Once it's straight, tighten all the 4 screws found on the stem of the scooter..

Stem wobble issues:

Tighten the screw found on the folding mechanism. There should be 2 on each side and 2 screws on the front. ( For reference: You can use allen wrench to tighten the screws)

Loose Rear wheel fix:

Step 1: Grab and push the wheel upwards.
Step 2: Just above the wheel, you will see two screws on each side. Tighten the screws while pushing the wheel upwards.
Step 3: Tighten these 4 screws that connect the wheel to the housing.

Deck play fix

Tighten these 6 screws on the black portion of the deck. You should see 3 screws on each side.

Kickstand Wiggle/Wobble

Tighten the screws above the kickstand. You should see 2 screws.